Heat and Lighting

Choosing a Heat Lamp: Bulbs, Ceramic Emitters and Wattage

Compare basking bulbs, ceramic heat emitters and deep heat projectors, and learn how to pick wattage and set up a reptile heat lamp safely.

On this page
  1. Short answer
  2. Basking bulbs (halogen and incandescent)
  3. Ceramic heat emitters
  4. Deep heat projectors and similar
  5. Colored and “night” bulbs
  6. Choosing wattage
  7. Fixtures, placement and safety
  8. Pair with a thermostat
  9. Picking by situation

Short answer

There is no single “best” heat lamp. The right one depends on whether you need daytime basking heat, night-time warmth without light, or both, and on the size and type of your enclosure. In general:

  • Halogen or incandescent basking bulbs suit daytime basking.
  • Ceramic heat emitters and deep heat projectors give heat without visible light, which suits night use or animals that do not need a bright basking spot.
  • Whatever you choose, pair it with a thermostat and check temperatures with your own thermometer.

Reptiles are ectotherms, so a heat source is how the enclosure replaces the sun. See are reptiles cold-blooded for the background.

Basking bulbs (halogen and incandescent)

These bulbs give off visible light and a broad range of infrared heat, which is why they are often chosen to imitate the sun.

  • Good for: daytime basking spots for lizards, turtles and snakes that bask.
  • Pros: produce both light and heat, easy to find, and many can be controlled with a dimming thermostat.
  • Cons: the light makes them unsuitable for night use, and the bulbs get very hot to the touch.
  • Tip: use them during the daytime light cycle only.

Ceramic heat emitters

Ceramic heat emitters (CHEs) are heating elements in a ceramic body that produce heat without visible light.

  • Good for: night-time heat and enclosures that need warmth at all hours.
  • Pros: no light to disrupt the day-night cycle, and they are long-lasting.
  • Cons: they mostly warm the air and surfaces rather than giving a sun-like basking effect, and they can dry out the enclosure. They also get extremely hot, so a guard is important.
  • Tip: check the thermostat’s manual to confirm what type of control it supports, since not every thermostat suits every emitter.

Deep heat projectors and similar

Deep heat projectors and related infrared emitters give off infrared heat without visible light. Some are marketed as a good all-around choice because they can be used day or night. They are typically more expensive than simple bulbs. Check the manufacturer’s information about their heat output and thermostat compatibility.

Colored and “night” bulbs

Red, blue or purple “night” bulbs are widely sold, but most experienced keepers advise against them. Visible colored light at night can interfere with a reptile’s day-night rhythm. A light-free emitter is usually a better choice for night heat. For more on how reptile vision differs from ours, see what colors can snakes see.

Choosing wattage

Wattage is where beginners most often go wrong, and there is no universal number. What matters:

  • Enclosure size. Larger enclosures need more heat output.
  • Top type. Screen tops let heat escape. Solid tops hold it in.
  • Distance from the bulb to the basking surface. Closer is hotter.
  • Room temperature. A cold room needs more heat.
  • The species’ target temperatures. Look these up for your animal.

A practical approach:

  1. Start with a modest wattage that is within the fixture’s rating.
  2. Measure the surface temperature of the basking spot with an infrared temperature gun or a probe, and the air temperature on both sides of the enclosure.
  3. Adjust the height or wattage, or use a thermostat or dimmer to fine-tune.
  4. Recheck at different times of day and as the seasons change.

Fixtures, placement and safety

  • Use a ceramic-socketed dome fixture or lamp rated for the wattage of the bulb. Plastic sockets can melt.
  • Place the lamp so the animal cannot touch the bulb. Use a wire cage or guard over the heat source where appropriate, since burns are a real risk, especially for snakes that climb or coil around objects.
  • Mount the lamp at one end to create a warm side and a cooler side, so the animal can move between them.
  • Keep cords and fixtures away from water and flammable materials, and never leave bulbs touching bedding or a plastic lid.
  • Replace blown or flickering bulbs, and never exceed the fixture’s wattage rating.

Pair with a thermostat

A heat lamp without a control can overheat an enclosure, especially if the room warms up or a bulb is replaced with a stronger one. A thermostat switches or dims the heat to hold your target temperature. See reptile thermostats: why you need one and how to set it up.

Picking by situation

  • Basking lizard or turtle in the daytime: a basking bulb, on a timer or dimming thermostat.
  • Snake kept in a cool room at night: a light-free option such as a ceramic emitter or similar, controlled by a thermostat. Some snakes also do well with other heating methods, so check what suits your species. For more on snakes in cool conditions, see can snakes survive the cold.
  • Reptile that needs UVB: heat and UVB are separate. For lizards, see choosing the right UVB bulb. See do snakes need UVB before assuming a heat bulb supplies it.

The complete guide to heat and lighting

Are Reptiles Cold-Blooded? How Ectotherms Regulate Heat
Read the guide

Keep exploring

Guides from other topics

All topics →