Short answer
A thermostat controls a heat source so that an enclosure stays near a target temperature instead of drifting up and down. For most reptile setups it is one of the most important pieces of equipment, because a heater running without control can overheat an enclosure, injure an animal or start a fire.
To set one up: plug the heater into the thermostat, plug the thermostat into the wall, place the probe at the right spot, set the target temperature, then verify with a separate thermometer before the animal goes in.
Why a thermostat matters
- Reptiles depend on external heat. A captive animal cannot move away from a heater that is too hot. See are reptiles cold-blooded.
- Heat output is not constant. Room temperature, season and bulb condition all change what a heater produces. A thermostat adjusts for that.
- It reduces burn and overheating risk, which are serious dangers for reptiles.
- It prevents the opposite problem of the enclosure becoming too cold, which can lead to poor digestion and illness. See can snakes survive the cold.
A thermostat is not a replacement for a thermometer, a guard around hot elements, or regular checks. It is one layer of protection.
Types of thermostat
- On/off (also called thermostats with switching control): turns the heater fully on when it is below the set point and fully off when it reaches it. Simple and common, and often used with heat mats. Temperatures can swing slightly above and below the target.
- Dimming thermostats: reduce the power to the bulb gradually, instead of switching it off. They are designed for bulbs that give off light and heat, such as basking bulbs, and keep the lamp lit while adjusting heat.
- Pulse proportional thermostats: switch the power on and off in rapid pulses, with a longer or shorter “on” share depending on how much heat is needed. They are intended for non-light heat sources, such as ceramic emitters or heat mats, and are not normally used with bulbs because the pulsing can make them flicker and shorten their life.
Always check the manufacturer’s instructions for what the thermostat is rated to control.
Matching the thermostat to the heater
| Heat source | Usually suits |
|---|---|
| Basking bulb (halogen or incandescent) | Dimming thermostat |
| Ceramic heat emitter | Pulse proportional, or other types the manufacturer approves |
| Heat mat or heat cable | On/off or pulse proportional |
For more on picking the heat source itself, see choosing a heat lamp. Also make sure the heater’s total wattage is within the thermostat’s rating.
Step-by-step setup
- Read the manuals for both the thermostat and heater.
- Choose a safe place for the thermostat outside the enclosure, away from water and the animal.
- Plug the heater into the thermostat, then plug the thermostat into the mains outlet.
- Install the probe (see below).
- Set the target temperature for the area where the probe sits.
- Switch on and watch. Leave it running for a while, ideally a day, without the animal inside, and check that it settles at the target and does not overshoot.
- Verify with an independent thermometer or infrared temperature gun. Compare readings from the probe and the second device, and check both the warm and cool ends of the enclosure.
- Adjust and repeat until the temperatures match your species’ guidance.
- Set up day and night settings if the thermostat allows it, so temperatures can drop at night where appropriate for the species.
Probe placement
Placement has a large effect on what the thermostat controls:
- Put the probe where the animal actually experiences the heat, such as at the level of the basking surface for a basking lamp. Keep it at the same distance from the heat source as the animal would be.
- For a heat mat, many guides suggest placing the probe near the mat’s surface, between the mat and the substrate or tank, so that the thermostat reads where the heat is delivered. Follow the thermostat’s instructions.
- Do not let the probe touch the heater directly, unless the instructions say so, since it will read a temperature far higher than the animal’s.
- Secure the probe so the animal cannot dislodge, chew or bury it, and so it cannot be dragged under hot objects.
- Keep the probe out of the animal’s reach if it might damage it, for example with a small guard or mesh.
Choosing the target temperature
Targets vary by species and by which part of the enclosure the probe sits in. A desert lizard, a tropical snake and a temperate turtle are all different. Use a reliable care guide or a reptile vet, and remember that you are aiming for a gradient, with a warmer area and a cooler area, not one uniform temperature.
Testing and ongoing checks
- Check temperatures every day or two, with a thermometer in a place the animal uses.
- Recheck after changing a bulb, moving the enclosure or when the seasons change.
- Replace any thermostat that behaves oddly, such as heating wildly above the set point.
- Consider a backup plan for power failures. See can snakes survive the cold for general tips.
Common mistakes
- Using a pulse thermostat with a bulb, or a dimmer with a device it is not designed for.
- Putting the probe too far from the heat source or in the cool zone, which makes the heater run too long.
- Trusting the thermostat’s display alone without checking with another thermometer.
- Exceeding the wattage rating of the thermostat.
- Letting the animal reach the heater, cable or probe.
Safety
Heaters and electrical equipment should be used according to the manufacturer’s guidance, kept dry and out of reach of the animal, and never covered or buried in a way the instructions prohibit. If you are unsure about wiring or safety, ask the retailer or a qualified electrician.