The short answer
To incubate snake eggs, keep them in a closed container on a slightly damp substrate inside an incubator that holds a steady temperature suited to the species, and avoid rotating them. Most common pet species hatch in around one to two months at their preferred temperature. Temperatures and humidity vary by species, so always confirm the figures for your snake before you set up.
Before you start: incubator and equipment
Set up and test the incubator before the eggs arrive. Run it for a few days to confirm it holds a steady temperature. You will usually need:
- An incubator, either a purpose-built reptile incubator or a well-insulated homemade setup.
- A thermostat. An accurate, reliable thermostat is the most important item. Overheating is a leading way to lose a clutch, so do not run a heat source without one.
- A thermometer and hygrometer, with the probe placed at egg level, and ideally a backup.
- Egg containers with a lid and a few small ventilation holes.
- Substrate (see below) and a sealed container for hatchlings later.
Handling and moving the eggs
- Do not rotate eggs. Mark the top of each egg lightly with a pencil if you need to move it, and keep it in the same orientation as laid. Turning can damage the embryo.
- Be gentle with clutches stuck together. Eggs laid together often stick to each other. Do not force them apart. Incubate them as a group.
- Move eggs soon after laying if you are removing them from the female, but handle them minimally.
- Wash and dry your hands, and avoid strong scents or chemicals.
Some keepers let a female that naturally broods, such as many pythons, incubate her own eggs. Using an incubator gives more control over temperature and humidity.
Choosing a substrate and setting humidity
Common incubation substrates include vermiculite and perlite. A frequently used approach is to mix the substrate with water by weight (for example, equal parts by weight) until it is damp but not dripping, though keepers use different ratios. Press a handful: it should hold together without leaking water.
Place the eggs partly pressed into shallow depressions, with the tops exposed, rather than burying them. Close the lid. Check that the substrate stays damp. If it dries out, add a small amount of water around the edges and not on the eggs. Humidity requirements differ among species, so check what is recommended for yours.
Temperature and incubation time
Different species do best at different temperatures, and incubation time goes up as the temperature drops. As rough, commonly cited ranges:
- Corn snakes are often incubated at around 78 to 82°F (about 26 to 28°C), and take roughly two months.
- Ball pythons are often incubated at around 88 to 90°F (about 31 to 32°C), and take roughly eight weeks.
Treat these as starting points and confirm them with species-specific guidance. Temperature should be stable: large swings can harm development, and a small difference can change the incubation length. Always measure at egg level, not just at the heat source.
Checking on the eggs
Check briefly and regularly, but avoid opening the container more than necessary.
- Candling. Shining a light through an egg can show blood vessels in a developing embryo, though it can take time and is not always conclusive. Be gentle.
- Dimpling and denting. A slightly dented egg can mean it needs moisture, and may recover. Resist adding water directly on it.
- Slugs. Infertile eggs are often small, yellow or hard. Many keepers remove obviously bad eggs, but wait if you are unsure, since some eggs look odd and still hatch. Eggs touching a bad egg can be affected, so remove one carefully only when clearly necessary.
- Mold. A little mold on a failing egg may appear. If it spreads, remove the egg and clean the container.
Hatching: what to expect
Near the end, a hatchling cuts one or more slits in the shell with a small egg tooth and often sticks its head out, a stage called pipping. It may remain in the egg for a day or even longer with its head showing, absorbing the last of the yolk. This is normal.
Do not pull a snake out. Leave the eggs undisturbed, keep conditions steady, and wait. If a hatchling has not emerged after a long time or seems stuck, consult a reptile veterinarian or an experienced breeder before intervening.
After hatching
Move hatchlings to a clean, warm, secure container once they have emerged on their own and are active. Provide water, and note that many hatchlings shed for the first time within the first week or two. Offer a first meal after that, appropriate for the species. Plan ahead for housing and feeding every baby, and for finding homes. See is breeding snakes profitable for the costs involved.
Common mistakes
- Running an incubator without a thermostat or testing it first.
- Rotating or flipping eggs.
- Overwatering, so that eggs sit in water.
- Opening the container too often, or letting it dry out.
- Removing a hatchling that is still in the egg.
- Assuming one species’ temperatures apply to another.
For background on where eggs come from, see how snakes mate and reproduce, and to understand what egg-laying and live birth mean for keepers, see live-bearing vs egg-laying snakes.